Case Study | Crack Warning on Lift Foundation, Platform Locking Loosening Hazard Identified

Release time:2026-11-19

In the automotive final assembly workshop, lifts are critical equipment for ensuring continuous line operation. As a core component that supports the lift’s stable operation, the belt roller base—when cracked or loose—can, at best, lead to increased vibration and accelerated roller wear; at worst, it may fracture or cause the lift to seize, directly disrupting the assembly cycle.

Recently, an entry lift in the final assembly workshop of a well-known automobile manufacturer successfully achieved early warning of belt roller base cracks by leveraging Zhongyun Technology’s intelligent operations and maintenance platform. By tracking trends and analyzing features, the platform detected anomalies during the gradual rise in vibration, guiding the company to carry out scheduled maintenance and preventing a production line shutdown caused by base fracture.

 

1. Vibrations gradually increase, triggering a trend alert on the platform.

On August 13, 2026, after the elevator was commissioned, platform monitoring detected that the vibration velocity on the left side of the belt roller bearing housing increased from 2 mm/s in August 2025 to 4 mm/s, triggering a trend threshold alarm. The system automatically pushed the alert to operations and maintenance personnel, clearly indicating the fault location, alarm level, and occurrence time, thereby pinpointing the target for on-site troubleshooting.

Figure 1: Equipment Model and Measurement Point Layout
 Image 2
Figure 2: Platform Alarm Information

 

II. Data-Driven Precision Diagnostics to Identify Base Loosening

Upon receiving the alert, the Zhongyun Diagnostics team analyzed the equipment’s operating parameters. The spectral analysis revealed prominent intermediate-frequency components, consistent with typical signs of basic loosening. Based on a comprehensive assessment, the platform determined that the left-side belt roller base is loose and recommended an immediate shutdown to inspect for abnormalities at the base.

 

Figure 3: Trend of vibration velocity characteristic values on the left side of the belt roller bearing housing

 

III. Shutdown Inspection Verification: Base Cracks Are Consistent with the Diagnosis

Based on the platform’s recommendation, a shutdown for inspection was scheduled on November 1. Upon disassembly and inspection, an obvious crack was found in the base of the left-side belt roller, which closely matched the platform’s diagnostic conclusion of “foundation loosening.” The maintenance team promptly replaced the faulty base.

 

dc1a089bb9f6b2d454d73690a13f8bae
Figure 4: On-site feedback diagram of pedestal cracks

 

IV. Post-maintenance verification: vibration significantly reduced

On the afternoon of November 11, the equipment was returned to service. Platform monitoring data show that the vibration velocity on the left side of the belt roller bearing housing has dropped below 1 mm/s, a significant decrease from the pre-maintenance level of 4 mm/s. The equipment’s operating trend has stabilized, and the potential hazard has been completely eliminated.

 

Figure 5: Vibration Velocity Trend After Maintenance

 

V. Lessons from the Case: Revealing “Hidden Cracks” in the Data

The successful early warning and planned maintenance for the crack fault in this lift’s base fully demonstrate the practical value of the online intelligent operations and maintenance platform in managing equipment at critical workstations in automobile manufacturing:

1. Trend tracking and early warning: An alarm is triggered when vibration slowly increases from 2 mm/s to 4 mm/s, providing a window for scheduled maintenance and preventing sudden shutdowns caused by worsening foundation cracks.

2. Data-driven, precise localization: Identify foundation looseness through frequency‑shift characteristics and guide on-site direct inspection of the base, avoiding indiscriminate disassembly and inspection.

3. Planned maintenance ensures continuity: With closed-loop management covering the entire process—from early warning and diagnostics to maintenance and verification—we mitigate potential downtime risks during scheduled maintenance windows, ensuring stable operation of the final assembly line.

 

Zhongyun Technology continues to deepen its expertise in industrial intelligent operations and maintenance. Leveraging monitoring data, it provides fault early warning and intelligent diagnostic services for critical equipment across various industries, helping enterprises shift from “reactive repairs” to “predictive maintenance.”

Make industry smarter and equipment healthier

%{tishi_zhanwei}%