I wish I had more time! Here's a tip to solve the problem of replacing batteries in wireless sensors!

Release time:2025-03-05

  In the wave of industrial intelligence, Zhongyun Technology's industrial intelligent wireless sensors are undoubtedly a powerful assistant for many enterprises. But like all devices, batteries need to be replaced. Don't worry, today we will provide you with a super detailed battery replacement tutorial to help you easily cope!

I. Prepare tools and materials

  New battery: Ensure that the model and specifications of the new battery are consistent with the old battery. You can find the battery model information on the sensor.

  Tools: Sponge single-sided adhesive tape, double-sided adhesive, scissors

II. Battery replacement steps

  SW3000 series wireless sensor battery replacement tutorial

  New battery preparation

  Measure 10 centimeters of sponge single-sided adhesive tape with a ruler and cut it with scissors. Tear off the yellow protective layer of the sponge single-sided adhesive tape.

  Take out the new battery, check if the plug and socket of the battery are firm and whether they have fallen off, and the metal surface of the socket is facing up to identify the polarity of the battery: black on the left and red on the right.

  Attach the sponge tape along the bottom of the battery 5 mm away, leaving a gap for the lead-out wires. Then carefully wrap it, maintaining moderate tightness to ensure that the sponge tape fits snugly against the battery surface. After wrapping, gently pinch both ends of the tape, ensuring that there is adequate space in the middle to facilitate the subsequent lead-out of the power cord and antenna.

  Remove the old battery

  Before removing the sensor with the battery that needs to be replaced, ensure that the sensor is powered off or in a non-working state to avoid damage or data loss during replacement. Clean the dust and oil stains on the surface of the removed sensor, then hold the bottom metal part of the sensor and unscrew the black plastic top cover.

  

 Zhongyun

 

  Hold the metal part of the sensor firmly, and use the other hand to steadily hold the battery, and gently shake it to smoothly pull the battery out of the sensor. During this process, be careful to avoid excessive force that may cause the power cord to break or unnecessary pulling on the circuit board. After removing the battery, continue to press the internal circuit board with your hand, and then carefully separate the battery plug from the circuit board.

  Install the new battery

  Make sure the red positive pole of the new battery is facing up, then hold the plug of the battery and insert the plug into the socket of the sensor circuit board, making sure that the wires of the plug are firmly inserted. Then, tightly clamp the antenna and power cord in the middle area of the battery, and press the battery sponge firmly and insert it into the shell. Finally, gently press the battery to slowly embed it in the shell.

  

 Zhongyun

 

  Use scissors to cut a piece of double-sided adhesive tape about two centimeters long and stick it to the bottom of the sensor's antenna sponge adhesive. Then, tear off the protective layer of the double-sided adhesive tape, attach the antenna sponge adhesive to the top of the battery, and gently press to ensure firm adhesion. Then, organize the power cord and antenna, and tighten the sensor's top cover. Finally, carefully check to make sure that all parts are correctly and firmly tightened. This completes the replacement of the new battery for the SW3000 series sensor.

  SW2000 series wireless sensor battery replacement tutorial

  Remove the old battery

  Unscrew the black cover of the SW2000 series sensor, carefully peel off the antenna above the battery, and carefully remove the battery, ensuring that the power cord and antenna are not broken. Use one hand to stabilize the bottom circuit board inside the sensor, then unplug the old battery plug to successfully remove the old battery and take out the battery protective sleeve.

  Install the new battery

  Insert the plug of the new battery into the socket of the circuit board and ensure that the connection is firm. Then, replace the battery protective sleeve inside the sensor. Because the length of the battery's power cord and antenna may be too long, it is necessary to bend the power cord and antenna appropriately when placing the battery in the lower end shell of the sensor.

  

 Zhongyun

 

  Then, cut two pieces of double-sided adhesive tape about two centimeters long and stick them to the top of the battery. After tearing off the double-sided adhesive tape, place the pad on top of the battery and gently press to ensure a firm fit. Then, re-attach the antenna to the pad. Finally, tighten the black cover of the sensor. This completes the entire battery replacement process.

  Testing and verification

  After replacing the battery, reconnect the power or start the sensor and perform a test to verify that it is working properly. Check if the sensor readings, signal transmission, and other functions are normal.

  III. Precautions

  1. Please operate carefully to avoid breaking the upper and lower connection points of the battery's power cord and antenna, which may damage the battery.

  2. Ensure that the plug of the new battery is firmly inserted into the socket of the circuit board to prevent poor contact from affecting the battery power supply. After replacing the battery, properly dispose of the old battery in time to avoid environmental pollution.

  3. The inside of the sensor has a sealed or waterproof design. When replacing the battery, pay special attention not to damage these designs, which may lead to reduced sensor performance or damage.

  Please note that the battery replacement steps may vary depending on the sensor model, so the above process is for reference only. In actual operation, please refer to the instructions or maintenance manual of the specific sensor for guidance. If you encounter difficulties or uncertainties, please contact Zhongyun Technology's technical support department for assistance.

Make industry smarter and equipment healthier

%{tishi_zhanwei}%